Pages

Showing posts with label benchmarks. Show all posts
Showing posts with label benchmarks. Show all posts

Saturday, July 4, 2015

Benchmarks of the Western Digital Green 4TB WD40EZRX drive

Header

I did a quick HD Tune benchmark run of one my recently purchased Western Digital Green 4TB drive.

WD40EZRX HDTune

HDTune 5.0 read benchmark of WD40EZRX drive

Compared to the 3TB drive that I used to own (and now sold), the sequential read speed has improved slightly (from 114MBps to 122MBps). However the access time has increased from 16.6ms to 17.1ms. You can check out the benchmarks of the 3TB drive, the WD30EZRX from this link.

CrystalDiskMark_4.0.3_x64_2015-07-03_23-21-15

Crystal Disk Mark 4.0.3 scores of WD40EZRX  drive

The Crystal Mark scores aren’t comparable with the benchmark scores on that page due to version mismatch as well as the tests were performed on an partially filled drive. The HDTune results should be more appropriate.

Friday, December 6, 2013

[Rant] 3DMark on the iPhone 5S

A couple of days ago I get to knew that they have released a version of 3DMark – the popular 3D gaming benchmark on the PC – for iOS.

photo 1

There are three tests that you can run.

And I ran all of them to see what scores it gave me.

photo

Sunday, November 17, 2013

[Article] How fast is the eMMC storage on the Asus Transformer Book T100 BayTrail tablet

Couple of weeks back I was ranting about how slow the eMMC storage on these Windows 8 tablets and that was the main cause of lag in them. You really need to have a proper SSD based storage on these tablets to really harness the power of the OS.

A week ago I bought my new Tablet and unfortunately it still came with eMMC storage. But I was hoping that it would be faster than the storage in the previous generation tablets. Today I ran Crystal Disk Mark to confirm it. Here are the results.

Asus Transformer Book T100

25w3

 

Sunday, November 3, 2013

[Rant] Speculating the performance of the upcoming NVidia GTX 780 Ti card

I'm sure most of you know that NVidia is planning to release a high end graphics card to counter the AMD R9 290X graphics card which sometimes even performs faster than the GTX Titan. Contrary to what the common sense product was, the latest rumors suggest that this is going to be a fully unlocked GK110 chip. That means, it will have 2880 sharers operating. The GTX780 has 2304 shaders and the Titan has 2688 shaders. That's 20% higher shaders count over the GTX 780 and 7% higher shaders count over the Titan.

Then, the clock speeds are getting an upgrade as well. The GTX 780 is clocked at 863MHz (900MHz boost) and the Titan is clocked at 836MHz (876MHz boost). The GTX 780 Ti will be clocked at 876MHz (928MHz boost). That's 3% higher clock speed over the GTX 780 and 6% higher clock speed over the Titan.

If you consider 100% scaling, we are looking at 23.6% performance boost over the GTX 780; 13% performance boost over the Titan. Best case, remember. But, we all know that the performance between the GTX 780 and the Titan is about 5%. In raw performance terms, the Titan is like 20% faster than the GTX 780. So, the scaling really sucks!

The GTX 780 Ti would be like 5% faster than the Titan at best. Which means, it would be like 5% faster than the R9 290X.

GeForce-GTX-780-TI

Basically, the R9 290X would still have a better price to performance ratio. 27% cheaper but only 5% slower. Basically, AMD doesn't have to worry about the GTX 780 Ti. But they sure have to worry about their production volume and the stupid stock cooler.

But then again, the stock cooler on the NVidia  card is very good. The rumor is that the card is capable of over- clocking to very high clocks. The AMD card suck over-clocking, no thanks to the crappy coder. According to this article, the GTX 780 Ti can be over-clocked  to 1240MHz which translates to about 23% performance boast over the R9 290X.And then there's is a GHz edition of the same GTX 780 Ti coming out a some point That would be about 10% faster than the R9 290X out of the box. But at what price? I'm sure NVidia would charge $799 for that card because it would be a heavily binned card and would be an overclocker's dream come true.

All I can say is that the R9 290X's pricing or even the GTX780's pricing (after the price drop) makes sense. Anything higher is just for the people who own a tree of money or who has little brain.

Edit:

Since I’ve posted this article, they have released the real thing and it is much faster than what I anticipated. It has made the Titan obsolete. The Titan was never meant to be a gaming card. I was a great compute card which you could buy without breaking the bank. However, it could do really well in games.

Thursday, July 18, 2013

[Article] Probably IvyBridge-E would be a flop as well

Yesterday Tom's Hardware released some preliminary benchmark results of the upcoming IvyBridge-E CPUs. They only compared others with the highest end SKU, namely, the 4960X. The results were very lackluster once again. (Previously, both the SB to IB and IB to Haswell were lackluster) I felt the benefits of IB-E over SB-E were even less than the benefits of IB over SB.
 
Now, there was one important improvement with IB-E over SB-E. Power consumption. At full load, the power consumption delta was more than 80W. This is at the same clock speeds. With the power consumption being lower than the predecessor and the IHS being soldered to the die, we might see some sweet overclocking numbers though. Too bad Tom's Hardware didn't do  any overclocking tests. That could be the deciding factor.
 
But if we assume that IB-E would clock to the same values as the SB-E, this doesn't look like a big upgrade either. You will definitely see a noticeable improvement with multi-threaded applications by upgrading to a 6-core CPU, but at what cost? The sweet spot, the 4930K, will still cost like $600. That's about 70% more than a 4770K, while giving less than 50% better results even at best case. On average, the 4930K would be like 20% faster. Maybe even less. Like I said, it is the overclocking potential that is going to make a difference.
 
Another noteworthy thing though. Why the heck would anyone buy a 4820K over a 4770K? It will perform about the same (because there isn't a noticeable difference between dual channel and quad channel memory and most people will settle for a maximum of 2 graphics cards; the enthusiasts will go for 6-core CPUs anyway), but 4770K has newer motherboards with 6x native SATA-III and USB3.0 support and a lot of fancy stuff. We all know that there is not going to be a x89 chipset, so the IB-E platform will be 2 years behind current technology. Sucks! Intel should have released IB-E last year.
 
I was planning to get the IB-E and now I'm skeptical. I will wait for the overclocking results - retail overclocking results to be precise. (We all know how Haswell retail CPUs clocks worse than the engineering samples.
 
Why, why, why doesn't Intel want my money? :(

Friday, June 7, 2013

Intel Rapid Storage Technology 12.5 is faster than 11.7

Remember I recently upgraded the firmware on my Samsung 840 series 250GB SSD? Even though the release notes said that I would see some performance improvements with the DXT08B0Q firmware, I didn’t see any. Then I upgraded the Intel Rapid Storage Technology drivers to see if it yielded in any improvements.

I originally had version 11.7.0.1013 installed. This was what I had when I flashed the firmware. There was a newer version out when I checked it a few days ago. Version 12.5.0.1066 (download from here). I don’t know what happened to version 12 though. Maybe I didn’t check for a new driver in a while. I only got to know that there was a newer driver from OCN forums.

I first uninstalled the old driver and installed the new one, just to be sure. Updating drivers doesn’t go really well most of the times. Ironically, I always update the NVidia drivers, never uninstall the old one and install the new one. I do that because I haven’t had issues doing so in the past. Sorry, I digress.

BTW, I downloaded the floppy driver, not the Windows drivers. The floppy driver comes with… just the RST driver. But the Windows driver comes with their monitoring and management software as well. Since I don’t use Smart Response Technology or RAID in my PC, there is no need to install them. No need to add more junk to the PC. I want to keep it as clean as possible.

Here are the benchmarks, before and after the update. Both were done after I updated the firmware to DXT08B0Q. For the entire specs of the test rig, click here.

Before (11.7.0.1013)

as-ssd-bench Samsung SSD 840  2013-06-01 8-54-44 AM

After (12.5.0.1066)

as-ssd-bench Samsung SSD 840  2013-06-01 8-58-47 AM

So you see, there is nice speed bump after the driver update. I don’t think that is a noticeable difference. Heck, you cannot feel the difference between two SSDs to the naked eye, without running benchmarks anyways. I just got this SSD because it was the cheapest 250GB one available back in January. not because it is the fastest.

Wednesday, June 5, 2013

Samsung 840 series 250GB Firmware Update: DXT08B0Q Benchmarks

Samsung released a new firmware for the Samsung 840 series (Pro and non-Pro both) few days ago. I didn’t upgrade that instant, because I saw on OCN forums that few people were having issues with the new firmware. I don’t want to end up with a dead drive. I don’t have a spare SSD lying around. Wish I kept that old SSD with me just in case something went wrong with the new one. But I didn’t and there is no point regretting about it. Have to move on.

But today I gave in, and went ahead with the update. What made me confident that something bad might not happen is because Samsung hadn’t pulled the firmware. That means there is nothing wrong with it to begin with. The people who got bad outcomes must have done something stupid. Just to be safe, I killed all the apps running in the foreground as well as background before starting the firmware update process.

I had DXT07B0Q firmware before update. You have to use Samsung SSD Magician software to do the firmware update. Even without me checking for an update manually, it automatically detected that there was a newer firmware available and highlighted in the UI of the software. Nothing amazing. That’s the way everything should work these days anyways. Just wanted to say that it is working as if should.

2013-06-01_08-50-34

Everything went smooth. It didn’t take long, and once done, the software told me that it needs to shutdown the PC to finish the update. What I didn’t know was that it would not automatically reboot. It was a clean shutdown, not a reboot. Some people might be confused by how it happened. With the previous drive, all that was required was a reboot. Anyways, now I know how it works in the future.

So did I see any gains with the new firmware? No! None at all. I recorded some benchmark scores on AS-SSD before and after the firmware update. Before running the test, I optimized the drive using the Magician software. Here are the results.

Note: Both tests were run with Intel Rapid Storage Technology ver. 11.7.0.1013 drivers.

Before update ( ver. DXT07B0Q )

as-ssd-bench Samsung SSD 840  2013-06-01 8-48-37 AM

After update ( ver. DXT08B0Q )

as-ssd-bench Samsung SSD 840  2013-06-01 8-54-44 AM

As you can see, the scores are identical. The difference would be attributed to measurement error. Well, at least the performance didn’t go down. That’s a relief.

Wednesday, May 15, 2013

Haswell dream shattered even before the release? Haswell is a flop?

Yesterday I came across a very disturbing news. A Chinese site had posted benchmark scores of the flagship Intel Core i7 4770K (@stock as well as at @4.5GHz) and the results were pretty bad. They were comparing it with the flagship model from the 3rd generation, namely the Core i7 3770K. They were not just posting the scores. They were also showing the screenshots of CPU-Z, AIDA and other benchmark programs. 

Let's be honest now. Nobody likes those Chinese sites. They are ugly, plus, nobody can read them. Google translate can do a decent job, but still the quality of content in those sites are BAD. Luckily, Xbitlabs recently extracted those results and posted on their website. Check it out by linking on the following link.
Web-Site Publishes Fully-Fledged Intel Core i7-4770K “Haswell” Review 

The following is an extract of the results posted on that site.


That really sucks! The only thing that might sound interesting is the last test, but that is all due to the better iGPU in Haswell. It has nothing to do with the CPU raw power.

But we knew that the performance improvement from the CPU side was not going to be fantastic. Intel was mostly concerned about two things. Improving the power efficiency (for tablets and ultrabooks) and improving the performance of the integrated graphics potion (for non-enthusiast crowd). They seems to have done that alright.

But we expected a bigger than a single digit percentage boost, did we not? In some tests, Haswell is even slower than its predecessor. That's unacceptable. The instructions per clock (or IPC) hasn't improved much, from even SandyBridge. For example, the 4770K@4.5GHz does 1M Super Pi calculations in 8.018s and my 2600K at same clocks does it in 8.344s. Just a mere 4% improvement at the same clocks. That's almost no architectural change IMO. No idea what those Intel engineers were doing for more than a year.

However, what every geek was waiting to see was how well the Haswell CPU overclocked compared to the previous generations. There were leaked overclocking results showing the CPU running at 6GHz with just 1.2V and 7GHz with a whopping 2.56V. It is possible that CPU-Z wasn't reporting the correct amount of Voltage because the Voltage Regulator Modules (VRMs) are moved from the motherboard on to the CPU itself. Anyways, 6GHz @1.2V seems like it can even do that on air, right? IvyBridge could do OK with 1.2V when it comes to the temperature. There is no need to doubt that would not be the case with Haswell because Intel did not change the process node from 22nm. 

But what that Chinese website reports is very troubling. They are saying that their 4770K CPU @4.5GHz could not complete Cinebench test because the internal temperature of the internals rose up too rapidly that their water cooler couldn't keep up with that rate, and ultimately crashing the PC. We don't really know if this is true or if they applied too much voltage to the CPU that it overheated too fast or if the reason for crash was something completely unrelated to it being a Haswell CPU. 4.5GHz seems to low to require a water cooler and that water cooler too being insufficient. Besides, this was a engineering sample. I don't think there would be significant difference between the retail product and this, but we shall see.

The CPUs are coming out in early June so it's only one month to go before we see the real things in action. But so far, things are not looking great for the enthusiast desktop user. If these results are true, I'll probably stick with my trusty Sandybridge CPU. Heck, I might even consider the IvyBridge-E platform to upgrade to. While I'm not happy that I won't be able to waste some of my hard earned cash this time round if Haswell turns out to be crap, I'm glad that this might actually give AMD a fighting chance when the Steamroller comes out later this year. (AFAIK, it's coming out in September so not so far away from now.)
Related Posts Plugin for WordPress, Blogger...